As long as you look carefully, there are many aerosol products in our daily life, such as spray paints, cleaners, insect sprays, cooking sprays and deodorants. Recycling an empty spray can may be as simple as throwing it into your curbside recycling bin. Recycling an entire can may require a trip to a local household hazardous waste facility. But no matter what condition your jar is in, it can be recycled. But before we can recycle, we need to clear up a few things. What are aerosol cans? Today, aerosol cans are made of either steel or aluminum. They have a plastic spray top and a plastic lid, and may contain a small piece of metal to help mix the product when the can is shaken. Inside the can is a liquid or gas that shoots out at a high rate of speed thanks to a chemical used as a propellant. In the past, chlorofluorocarbons (also known as CFCs) were the most common propellant. When people realized CFCs were one of the primary gases destroying the ozone layer, they were banned in most countries and aerosol can manufacturers were forced to find another propellant. Today, food products use carbon dioxide or nitrous oxide as propellants, while others use propane or butane as the propellant. CFCs in very small quantities are still approved for a few uses, including asthma inhalers. Why should I recycle aerosol cans? You should recycle an empty aerosol can because the metal is fully recyclable and can be put back to use as new products. However, you should absolutely not recycle a can that is not empty because it can explode. Aerosol cans with even a little paint or bug spray still contain some of that propellant, and they can blow up under pressure, injuring sanitation workers or damaging equipment. In addition, insecticides and other dangerous chemicals left in the can need to be disposed of in a way that will not hurt the environment. How to recycle aerosol cans? If possible, use up all the material in your can. Empty aerosol cans are treated like any other type of steel or aluminum can. The process for recycling full aerosol cans is simple. Using special equipment punches a hole in the can and allows any remaining liquid to drain out. The liquid is kept in a secure container so it can be disposed of properly. The empty metal can is sent to a metal recycler. Your task is to get that full can to someone qualified to recycle it. In most cases, that recycler will be your community's household hazardous waste center. Be sure and check with your local program to determine its hours, fees and if it has limits on the quantity of material it will accept at any given time.  Welcome to visit our homepage to know more about aerosol cans www.mgaerosolcan.com 

What performance tests are required for aerosol cans？ 1. Appearance Quality Visually inspect the sample under natural light, including checking for defects, imperfections, and other inspection items. Testing: The purpose is to record the physical appearance of the sample to determine if the aerosol can is flat and free of rust spots. Aerosol can with internal coating, the internal coating should be uniform and free of protrusions and impurities. The printed graphics and text are clear and complete, with no obvious scratches on the main parts. 2. Size The height of the can body, total height, crinkle height, the outer diameter of the aerosol can opening, the inner diameter of the aerosol can opening,the outside dia of the double seam and height of the double seam should all be within the specified deviation range. Testing: You can learn about the specifications of the aerosol cans you produce and whether they meet the technical requirements for sealing samples 3. Integrity of weld coating The integrity of weld coating refers to the coverage area of the weld coating and the adhesion performance between the coating and the substrate, used to protect the weld and its surrounding areas from corrosion and environmental damage. Testing: Integrity testing of weld coating can detect defects in both weld and coating, such as porosity, inclusions, cracks, and other defects inside the weld, or defects such as bubbles, peeling, and pitting on the coating surface. If these defects are not detected and addressed in a timely manner, they may affect the sealing and safety performance of the aerosol can, and even lead to serious accidents such as aerosol can explosions. 4. Adhesion of inner and outer coatings of aerosol cans The adhesion between the inner and outer coatings of aerosol cans refers to the adhesion performance between the coating and the substrate, which is an important parameter of coating performance. Testing: Internal and external coating adhesion testing can ensure that the adhesion performance between the coating and the substrate meets the standard requirements, avoiding the occurrence of coating peeling, cracking, or detachment. This can not only extend the service life of aerosol cans, but also improve their safety and reduce potential hazards. 5. Hardness of the outer coating of the aerosol can The hardness testing of the outer coating is to ensure the wear resistance and scratch resistance of the surface of the aerosol can during use. Testing: The outer coating hardness test can evaluate the hardness and scratch resistance of the coating, thereby determining the quality and durability of the coating. In addition, the hardness test of the outer coating can also detect quality issues of the coating, such as possible defects such as air bubbles and sagging, which may cause coating detachment or surface damage, thereby affecting the safety performance of the aerosol can. 6.Air tightness performance of aerosol cans Airtightness performance testing refers to determining the airtightness performance of an aerosol can under pressure differences inside and outside the can by testing its sealing performance. Testing: Aerosol cans need to withstand a certain amount of pressure during use, so their sealing performance has a significant impact on their safety and service life. If the airtightness performance is poor, it may lead to excessive internal pressure or leakage of the aerosol can, thereby causing safety accidents. 7. Deformation pressure Deformation pressure testing refers to the pressure testing of an aerosol can to determine whether it can withstand a certain amount of pressure deformation without breaking. Testing: During use, aerosol cans may be affected by external forces such as collision, compression, etc. If the structure of the aerosol can cannot withstand a certain amount of deformation pressure, deformation or rupture may occur, leading to safety accidents. 8. Burst pressure Burst pressure testing refers to the process of conducting pressure tests on aerosol cans to determine their maximum allowable pressure. Testing: During the use of aerosol cans, due to changes in pressure and environmental influences, the internal pressure may suddenly increase, leading to serious accidents such as explosions. Therefore, when manufacturing aerosol cans, it is necessary to conduct a burst pressure test to ensure their safety performance within the normal operating pressure range. Compatibility and hygiene requirements testing can be conducted based on customer requirements and product properties.